Loading... 环境:两台2500系列路由器通过串口相连。 要求:在R1和R2上启用静态路由,使两端网络能够互通。 步骤一、基本配置 Router> Router>enable Router#config terminal Router(config)#hostname R1 R1(config)#no ip domain-lookup R1(config)#line console 0 R1(config-line)# logging synchronous R1(config-line)#exec-timeout 0 0 R1(config-line)#exit 步骤二:接口配置 R1的配置: R1(config)#interface s0 R1(config-if)#ip address 30.1.1.1 255.255.255.0 R1(config-if)#clock rate 64000 时钟速率端 R1(config-if)#no shutdown R1(config-if)#interface loopback 0 R1(config-if)#ip address 10.1.1.1 255.255.255.0 R1(config-if)# R2的配置: Router(config)#hostname R2 R2(config)#interface s1 R2(config-if)#ip address 30.1.1.2 255.255.255.0 R2(config-if)#no shutdown R2(config-if)#interface loopback 0 R2(config-if)#ip address 20.1.1.1 255.255.255.0 R2(config-if)#exit R2(config)# 步骤三、指定静态路由<!--more--> R1(config)# R1(config)#ip route 20.1.1.0 255.255.255.0 serial 0 指定静态路由 R2(config)# R2(config)#ip route 10.1.1.0 255.255.255.0 30.1.1.1 指定静态路由 步骤四、作ping 测试 R1#ping Protocol [ip]: Target IP address: 20.1.1.1 目的地址 Extended commands [n]: y 是否用扩展命令 Source address or interface: 10.1.1.1 源地址 !!!!! 显示已通 步骤五、显示静态路由条目 R1#show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set 20.0.0.0/24 is subnetted, 1 subnets S 20.1.1.0 is directly connected, Serial0 静态路由条目 10.0.0.0/24 is subnetted, 1 subnets C 10.1.1.0 is directly connected, Loopback0 30.0.0.0/24 is subnetted, 1 subnets C 30.1.1.0 is directly connected, Serial0 步骤六、显示当前配置 R1的配置结果: R1#show running-config ! hostname R1 ! no ip domain-lookup ! interface Loopback0 ip address 10.1.1.1 255.255.255.0 ! interface Serial0 ip address 30.1.1.1 255.255.255.0 clockrate 64000 ! ip route 20.1.1.0 255.255.255.0 Serial0 ! line con 0 exec-timeout 0 0 logging synchronous transport input none end R2的配置结果: R2#show running-config ! hostname R2 ! no ip domain-lookup ! interface Loopback0 ip address 20.1.1.1 255.255.255.0 ! interface Serial1 ip address 30.1.1.2 255.255.255.0 ! ip route 10.1.1.0 255.255.255.0 30.1.1.1 ! line con 0 exec-timeout 0 0 logging synchronous ! end Last modification:October 6, 2023 © Allow specification reprint Support Appreciate the author AliPayWeChat Like 如果觉得我的文章对你有用,请随意赞赏
One comment
呵呵,还好!!小凡嘛!